Back to Top Skip to main content Skip to sub-navigation

Medical tools, supplies 3D printed in desert deployment

Army Lt. Col. Jason Barnhill, a faculty member of West Point and the Uniformed Services University’s Department of Radiology, poses for a photo with a 3D printer capable of biofabrication that could expedite repair or perhaps replace damaged tissues for troops injured on the battlefield. (Courtesy photo) Army Lt. Col. Jason Barnhill, a faculty member of West Point and the Uniformed Services University’s Department of Radiology, poses for a photo with a 3D printer capable of biofabrication that could expedite repair or perhaps replace damaged tissues for troops injured on the battlefield. (Courtesy photo)

Recommended Content:

Technology

The ability to 3D print a variety of healthcare-related products in deployed locations would greatly benefit the nation’s warfighters.

A recent pilot program conducted by the Uniformed Services University of the Health Sciences (USU) in collaboration with the U.S. Military Academy at West Point has shown that a 3D printer capable of biofabrication could expedite repair or perhaps replace damaged tissues for troops injured on the battlefield. This advancement could potentially change the way care deployed warfighters receive care.

The pilot program, called Fabrication in Austere Environments, or Fab AE, was developed by USU’s 4-Dimensional Bioprinting, Biofabrication, and Biomanufacturing Program (4D Bio3). 4D Bio3 is a federally-funded program to develop new technologies to support medical treatment and training solutions for warfighters.

The Fab AE initiative is a collaborative effort between USU, West Point, and The Geneva Foundation, along with NScrypt and Techshot, and sought to demonstrate whether 3D printers could be forward-deployed into desert environments to fabricate medical products in austere settings where resources may be limited. The ruggedized 3D printer was sent to an undisclosed desert location with basic supplies and human mesenchymal stem/stromal cells (hMSCs), the only cells that allow for same-day bioprinting.

On site, Army Lt. Col. Jason Barnhill, a faculty member of West Point and USU’s Department of Radiology, led the project. Under his direction, the 3D printer successfully fabricated a number of products, including a scalpel capable of immediate use; and a hemostat, a surgical tool used to control bleeding during surgery and capable of gripping objects, while locking them into place to hold tissue or other medical implements. The tools were made of material that could be sterilized on site, reducing the chance of infection during practical use.

Barnhill was also able to develop bioactive bandages by printing a hydrogel layer of antibiotics over a structural layer, all within just five minutes. The bandages were designed to slowly release antibiotics into the wound, prolonging the suppression of bacteria for several days. The bacterial suppression and actual bandage design could also be tailored, using CT data, to alter the amount antibiotic concentration as needed.

Additionally, the 3D printer fabricated a surgical model of a T9 vertebrae, one of the lower thoracic spinal vertebrae that provides structural support for the spinal cord. Fractures of the lower thoracic spine may result in paraplegia, and/or loss of bowel/bladder control. The image for this surgical model was obtained from medical scans, and while it could not be implanted in a patient, it would be invaluable to on-site surgeons, helping them to visualize musculoskeletal injuries and determine the best course of surgical intervention.

The 3D bioprinter was also able to produce a meniscus, cartilage in the knee that acts as a shock absorber. The image used to print the meniscus was sent as an electronic file from a stateside facility to the remote environment, and printed on location – the first demonstration of cyber manufacturing where complex designs were transmitted and produced in a remote location.

In parallel to this initiative, a 3D printer had previously been sent to the International Space Station where astronauts are currently running similar 3D printing experiments. The hope is to send the printer aboard one of the Navy’s hospital ships, the USNS Mercy.

“We believe this program has the potential to reduce logistical challenges and costs for transporting medical supplies to austere environments, which could also be applied to our special operations forces in remote locations. Instead of carrying tons of supplies, they could just print them using a, hopefully, more portable, light-weight version in the future that could fit in their pack,” said Dr. Vincent Ho, director of USU’s 4D Bio3, principal investigator for the FAB AE initiative, and chair of USU’s Department of Radiology. “3D printing provides the ability to produce tailored health care solutions that meet the specific needs of the warfighter deployed to austere locations. The ability to build health-related products in near real time when and where needed enhances operational flexibility for our commanders in the field. As we continue to meet the needs of our nation’s warfighters, this pilot project is also the first step in manufacturing health care products on-site to help identify and treat battlefield injuries and medical conditions.”

Disclaimer: Re-published content may be edited for length and clarity. Read original post.

You also may be interested in...

October 2018 Post Test

Presentation
10/15/2018

Recommended Content:

Technology

October 2018 Webinar

Presentation
10/15/2018

October 2018 Webinar

Recommended Content:

Technology

Cyberfit Poster Navy Family 2018

Publication
10/5/2018

This poster urges Navy personnel to teach their children online safety.

Recommended Content:

Technology

Cyberfit Poster Baby Monitor 2018

Publication
10/5/2018

This poster urges military families to make sure their baby monitors and home internet connection are properly secure.

Recommended Content:

Technology

Cyberfit Poster: AirForce Family 2018

Publication
10/5/2018

This poster urges AirForce personnel to teach their children online safety.

Recommended Content:

Technology

Cyberfit Poster Guard Your Cell Phone 2018

Publication
10/5/2018

This poster urges military families to keep an eye on their cell phones, as anyone could take them, even their dog.

Recommended Content:

Technology

Cyberfit Poster: Military Family Readiness 2018

Publication
10/5/2018

This poster urges military personnel to teach their children online safety.

Recommended Content:

Technology

Cyberfit Poster: Work with Kids 2018

Publication
10/5/2018

This poster urges military parents to make sure their families are CyberFit.

Recommended Content:

Technology

Cyberfit Poster Think Twice 2018

Publication
10/5/2018

This poster urges military family members to think twice before posting something online.

Recommended Content:

Technology

Cyberfit Fact Sheet: Medical Devices 2018

Fact Sheet
10/5/2018

This Fact Sheet describes medical devices and provides basic guidelines on keeping them secure and safe.

Recommended Content:

Technology

Cyberfit Family FactSheet 2018

Fact Sheet
10/5/2018

This Fact Sheet provides information about what Cyber Security is and how to remain safe while online.

Recommended Content:

Technology

Desktop to Datacenter initiative explained at DHITS 2018

Photo
7/26/2018
Mark Goodge, chief technology officer for the Defense Health Agency, speaks to attendees of the Defense Health Information Technology Symposium about the agency Desktop to Datacenter initiative.

Mark Goodge, chief technology officer for the Defense Health Agency, speaks to attendees of the Defense Health Information Technology Symposium about the agency Desktop to Datacenter initiative.

Recommended Content:

Defense Health Agency | Defense Healthcare Management Systems | Technology | Federal Electronic Health Record Modernization (FEHRM) Program Office | MHS GENESIS

MHS Health IT Awards

Photo
7/24/2018
On July 24, 2018, at the Defense Health Information Technology Symposium in Orlando, Fla., Service members and employees from across the Military Health System were recognized who have made significant contributions and demonstrated outstanding excellence and achievement in Health Information Technology (HIT) in the past year.

On July 24, 2018, at the Defense Health Information Technology Symposium in Orlando, Fla., Service members and employees from across the Military Health System were recognized who have made significant contributions and demonstrated outstanding excellence and achievement in Health Information Technology (HIT) in the past year.

Recommended Content:

Technology | Assistant Secretary of Defense for Health Affairs | Defense Health Agency

DHITS 2018

Video
7/18/2018
DHITS 2018

This video describes the important topics covered during the Defense Health Information Technology Symposium each year

Recommended Content:

Technology

TRICARE Online Patient Portal Mobile

Fact Sheet
7/16/2018

This fact sheet provides an overview of TRICARE Online Patient Portal (TOL PP) Mobile enabling beneficiaries to access TOL PP with any mobile device including smart phones. The fact sheet includes instructions on how to access TOL PP Mobile.

Recommended Content:

Technology
<< < ... 6 7 8 > >> 
Showing results 76 - 90 Page 6 of 8

DHA Address: 7700 Arlington Boulevard | Suite 5101 | Falls Church, VA | 22042-5101

Some documents are presented in Portable Document Format (PDF). A PDF reader is required for viewing. Download a PDF Reader or learn more about PDFs.