Back to Top Skip to main content Skip to sub-navigation

Medical tools, supplies 3D printed in desert deployment

Army Lt. Col. Jason Barnhill, a faculty member of West Point and the Uniformed Services University’s Department of Radiology, poses for a photo with a 3D printer capable of biofabrication that could expedite repair or perhaps replace damaged tissues for troops injured on the battlefield. (Courtesy photo) Army Lt. Col. Jason Barnhill, a faculty member of West Point and the Uniformed Services University’s Department of Radiology, poses for a photo with a 3D printer capable of biofabrication that could expedite repair or perhaps replace damaged tissues for troops injured on the battlefield. (Courtesy photo)

Recommended Content:

Technology

The ability to 3D print a variety of healthcare-related products in deployed locations would greatly benefit the nation’s warfighters.

A recent pilot program conducted by the Uniformed Services University of the Health Sciences (USU) in collaboration with the U.S. Military Academy at West Point has shown that a 3D printer capable of biofabrication could expedite repair or perhaps replace damaged tissues for troops injured on the battlefield. This advancement could potentially change the way care deployed warfighters receive care.

The pilot program, called Fabrication in Austere Environments, or Fab AE, was developed by USU’s 4-Dimensional Bioprinting, Biofabrication, and Biomanufacturing Program (4D Bio3). 4D Bio3 is a federally-funded program to develop new technologies to support medical treatment and training solutions for warfighters.

The Fab AE initiative is a collaborative effort between USU, West Point, and The Geneva Foundation, along with NScrypt and Techshot, and sought to demonstrate whether 3D printers could be forward-deployed into desert environments to fabricate medical products in austere settings where resources may be limited. The ruggedized 3D printer was sent to an undisclosed desert location with basic supplies and human mesenchymal stem/stromal cells (hMSCs), the only cells that allow for same-day bioprinting.

On site, Army Lt. Col. Jason Barnhill, a faculty member of West Point and USU’s Department of Radiology, led the project. Under his direction, the 3D printer successfully fabricated a number of products, including a scalpel capable of immediate use; and a hemostat, a surgical tool used to control bleeding during surgery and capable of gripping objects, while locking them into place to hold tissue or other medical implements. The tools were made of material that could be sterilized on site, reducing the chance of infection during practical use.

Barnhill was also able to develop bioactive bandages by printing a hydrogel layer of antibiotics over a structural layer, all within just five minutes. The bandages were designed to slowly release antibiotics into the wound, prolonging the suppression of bacteria for several days. The bacterial suppression and actual bandage design could also be tailored, using CT data, to alter the amount antibiotic concentration as needed.

Additionally, the 3D printer fabricated a surgical model of a T9 vertebrae, one of the lower thoracic spinal vertebrae that provides structural support for the spinal cord. Fractures of the lower thoracic spine may result in paraplegia, and/or loss of bowel/bladder control. The image for this surgical model was obtained from medical scans, and while it could not be implanted in a patient, it would be invaluable to on-site surgeons, helping them to visualize musculoskeletal injuries and determine the best course of surgical intervention.

The 3D bioprinter was also able to produce a meniscus, cartilage in the knee that acts as a shock absorber. The image used to print the meniscus was sent as an electronic file from a stateside facility to the remote environment, and printed on location – the first demonstration of cyber manufacturing where complex designs were transmitted and produced in a remote location.

In parallel to this initiative, a 3D printer had previously been sent to the International Space Station where astronauts are currently running similar 3D printing experiments. The hope is to send the printer aboard one of the Navy’s hospital ships, the USNS Mercy.

“We believe this program has the potential to reduce logistical challenges and costs for transporting medical supplies to austere environments, which could also be applied to our special operations forces in remote locations. Instead of carrying tons of supplies, they could just print them using a, hopefully, more portable, light-weight version in the future that could fit in their pack,” said Dr. Vincent Ho, director of USU’s 4D Bio3, principal investigator for the FAB AE initiative, and chair of USU’s Department of Radiology. “3D printing provides the ability to produce tailored health care solutions that meet the specific needs of the warfighter deployed to austere locations. The ability to build health-related products in near real time when and where needed enhances operational flexibility for our commanders in the field. As we continue to meet the needs of our nation’s warfighters, this pilot project is also the first step in manufacturing health care products on-site to help identify and treat battlefield injuries and medical conditions.”

Disclaimer: Re-published content may be edited for length and clarity. Read original post.

You also may be interested in...

Defense Medical Logistics Standard Support Customer Assistance Module (DCAM)

Fact Sheet
10/1/2013

DCAM allows customers to download medical supply catalogs and place orders for medical supplies.

Recommended Content:

Technology | Medical Logistics

Defense Health Agency Update

Presentation
6/27/2013

Defense Health Agency Update presented to the Defense Health Board

Recommended Content:

Technology

Waiver of Restrictive Licensure and Privileging Procedures to Facilitate the Expansion of Telemedicine Services in the Military Health System 12-010

Policy

In order to facilitate the expansion of telemedicine services in the Military Health System, this memorandum waives selective provisions of Department of Defense 602S.13-R, "Clinical Quality Assurance in the Military Health System," June 11 , 2004. This waiver is conditioned on the specific provisions of this memorandum, and shall remain in effect, unless modified or revoked, until the cancellation and reissuance of DoD 602S.13-R, or the issuance of a Department of Defense Instruction for or including telemedicine.

MHS Enterprise Architecture Signed Memo and Guide 20120730

Policy

Announcement of the release of the Military Health System (MHS) Enterprise Architecture (EA) Guide. The guide supports the MHS CIO’s responsibilities for development and maintenance of EA, which complies with the Department of Defense’s responsibilities under the Clinger-Cohen Act of 1996, Public Law 104-106.

  • Identification #: 00-memo-2012-07-30
  • Date: 7/30/2012
  • Type: Memorandums
  • Topics: Technology

Guidance on the Establishment of a Human Cell, Tissue, and Cellular and Tissue Based Products Program

Policy

This memorandum requests the Services resource a Human Cell, Tissue, and Cellular and Tissue Based Products (HCT/Ps) Program that complies with regulatory standards for management and oversight of HCT/Ps, according to the best fit for their Service.

Standard Enterprise Architecture Requirements for Acquiring Information Management/Information Technology Products and Services

Policy

The Military Health System (MHS) Information Management/Information Technology (IM/IT) Strategic Plan established enterprise-wide interoperability and common architecture goals for MHS 1M/IT products and services that promote agility and interoperability within MHS and externally with Federal and industry partners.

  • Identification #: 00-memo-2012-06-19
  • Date: 6/19/2012
  • Type: Memorandums
  • Topics: Technology

MHS Cloud First Adoption Directive and Policy Guidance Signed Memo and Attachment

Policy

The National Defense Authorization Act for Fiscal Year (FY) 2012 mandates that the Department of Defense (DoD) and its agencies develop a strategy to migrate to using Cloud computing services. Against this backdrop, DoD released an IT Enterprise Strategy and Roadmap plan in September 2011 developed by the DoD CIO, Teri Takai. This memorandum is consistent with Federal and DoD strategies, directives, and plans as they relate to implementation of a Military Health System (MHS) Cloud First policy aligning with the MHS mission

  • Identification #: 00-memo-2012-05-22
  • Date: 5/22/2012
  • Type: Memorandums
  • Topics: Technology

Army Health Promotion and Risk Reduction Campaign

Presentation
10/1/2009

Army Health Promotion and Risk Reduction Campaign presented to the Defense Health Board Oct. 1, 2009

Recommended Content:

Technology | Suicide Prevention
<< < ... 6 7 8 > >> 
Showing results 106 - 113 Page 8 of 8

DHA Address: 7700 Arlington Boulevard | Suite 5101 | Falls Church, VA | 22042-5101

Some documents are presented in Portable Document Format (PDF). A PDF reader is required for viewing. Download a PDF Reader or learn more about PDFs.