Back to Top Skip to main content Skip to sub-navigation

Army, FDA discuss 3D printing at workshop

When a medical device breaks down on a medical unit deployed to a remote part of the world, the closest repair parts could be thousands of miles away (U.S. Army photo by Francis S. Trachta) When a medical device breaks down on a medical unit deployed to a remote part of the world, the closest repair parts could be thousands of miles away (U.S. Army photo by Francis S. Trachta)

Recommended Content:

Military Hospitals and Clinics | Technology | Combat Support | Medical Logistics

FORT DETRICK, Md. — When a medical device breaks down on a U.S. Army unit deployed to a remote part of the world, the closest repair parts could be thousands of miles away.

Even when parts are readily available, the shipping process – sometimes into hostile environments – could take days or even weeks, if it’s logistically feasible at all.

As the Army embraces advanced manufacturing in its modernization strategies, medical logisticians are looking to 3D printing as a potential solution to this challenge.

"The medical industry is one of the fastest innovators in the defense industrial base, so the AMLC is used to working with industrial partners constantly pushing the state of the art,” said Jack Rosarius, director of Medical Maintenance Management Directorate within the U.S. Army Medical Materiel Agency, a direct reporting unit to Army Medical Logistics Command.

Specifically for medical devices, 3D printing technology – also known as additive manufacturing – may enable the Army to develop repair parts that extend the life cycle of equipment and ensure they are ready for use when and where Soldiers need them.

While the technology offers numerous new uses and potential advantages, it also poses regulatory challenges and warrants safety considerations still under review by the U.S. Food and Drug Administration.

On Dec. 9, 2019, AMLC hosted a military-specific workshop at Fort Detrick with FDA leaders on the topic to seek guidance on current policies, concept regulations and potential stumbling blocks as it explores manufacturing its own repair parts and other 3D-printed items.

Representatives from Army Materiel Command, Air Force and Defense Health Agency also took part in the discussion.

‘Really excited’

USAMMA started piloting additive manufacturing in 2015 in partnership with its equipment program managers. Rosarius said a heightened top-down focus from Army senior leadership has only helped to push the 3D printing movement forward.

“I’m really excited about the opportunities,” said USAMMA Commander Col. Timothy D. Walsh, who also serves as deputy commander of AMLC. “It’s an exciting time to be a part of Army medicine.”

The 3D printing process involves building a three-dimensional object using a computer-aided design model by adding material layer by layer, which is why it’s called additive manufacturing.

The process differs from conventional machining, casting or forging, in which material is removed from a stock item or poured into a mold and shaped to form a product.

Through 3D printing, medical devices can be produced using a range of media, including metals, plastics, hydrogels or even biological materials. Most printing systems do this by dividing or slicing a digital design file in two-dimensional layers, then building each layer on top of the previous layer.

According to the FDA, medical companies began embracing additive manufacturing to create devices that were previously impossible to make, personalized to the patient or both.

‘Gray areas’

While the technology has unlocked new production possibilities, it also has prompted the FDA to explore conceptual regulations to safeguard patients and institute performance requirements.

“The FDA is very focused on what the risk is and how to mitigate it” with 3D-printed medical products, said Matthew A. Di Prima, materials engineer for the agency.

Heather L. Agler, a senior program manager for the FDA, said the technology has created new “gray areas,” specifically when it comes to military production and uses.

Patient safety, however, remains the overarching issue under consideration by federal regulators.

Army’s commitment

During the workshop, AMLC officials gave an overview of the Army’s Advanced Manufacturing Directive and briefed the FDA on efforts to date.

USAMMA has made successful use of 3D printing to produce some obsolete repair parts already, like an impeller for a medical sink or a locking pin for a vaporizer used on an anesthesia machine.

Many more are in various stages of development or design.

“The Advanced Manufacturing Directive demonstrates the Army's commitment to getting this right, so we're positioned for multi-domain operations and large-scale combat operations,” Rosarius said. “The medical maintenance community is excited about expanding the ways we can support patient care downrange.”

Di Prima highlighted different additive manufacturing use-cases, in addition to current agency policy considerations for manufacturers.

The group also worked through different Army-specific scenarios to identify possible snags for ongoing or future efforts, as well as several action items for further discussion.

“We’re happy to participate,” Agler said. “The military is always thinking forward. It’s good to be able to learn … and very important that we continue to work together to make sure you have the right things available when they are needed.”

Disclaimer: Re-published content may be edited for length and clarity. Read original post.

You also may be interested in...

USAMRIID scientist recognized by French for distinguished service

Article
12/4/2020
Two military officers on stage; one handing the other a certificate

Kugelman...identified genetic markers of persistence of the Chikungunya virus.

Recommended Content:

Health Readiness | Research and Innovation | Technology

Military medicine confronts an invisible enemy

Article
12/4/2020
Medical personnel set up in an outside military tent

The collective response to the pandemic underscored the MHS reputation for innovation, with practical applications beyond military medicine.

Recommended Content:

Combat Support | Warrior Care | Public Health | Coronavirus | Heroes Behind the Mask

New report finds military hearing health is improving

Article
12/3/2020
Military doctor inspecting patient's ear

Noise-induced hearing loss is decreasing for active-duty service members.

Recommended Content:

Combat Support | Health Readiness | Hearing and Balance Injuries | Hearing Center of Excellence

DGMC medical study looks at plant-based diet

Article
12/3/2020
Man wearing mask and gloves putting container of salad into salad bar

Researchers measured important cholesterol, weight and blood pressure markers at baseline and at 4-weeks.

Recommended Content:

Combat Support | Health Readiness | Nutritional Fitness

METC improves surgical tech training with new laparoscopy standard

Article
12/1/2020
Surgical team in operating room

A laparoscopy is a low-risk, non-invasive surgical procedure used to examine organs inside the abdomen and repair or remove tissue.

Recommended Content:

Combat Support | Health Readiness | Research and Innovation | Technology

BAMC recognized by American College of Surgeons for outstanding care

Article
11/27/2020
Medical team, wearing masks, rushing a patient in a hospital bed down the hallway

“BAMC provides more complex care to the nation than any other military treatment facility..."

Recommended Content:

Health Readiness | Combat Support | Clinical Quality Management | Quality and Safety of Health Care (for Healthcare Professionals) | Readiness Capabilities

DHA improves financial efficiency with consolidated funding system

Article
11/20/2020
Soldier wearing mask, marking items off in supply room

The conversions enable GFEBS financial structure and funding control by the DHA.

Recommended Content:

Technology | Business Support

NMRTU Everett staff collaborate to ensure Patient Centered Care

Article
11/16/2020
Image of two military personnel wearing masks

NMRTU Everett was commended by the MHS 2020 Advancement towards High Reliability Healthcare Awards Program as a Patient Centeredness Award winner.

Recommended Content:

Combat Support | Public Health | Coronavirus

Naval Medical Forces Pacific’s commander tours NH Twentynine Palms

Article
11/12/2020
Four military personnel in uniform, wearing masks

Weber was briefed on the implementation of MHS GENESIS...and the hospital's response to COVID-19.

Recommended Content:

Combat Support | Health Readiness | Coronavirus | Electronic Health Record: MHS GENESIS | Readiness Capabilities

Walter Reed, VA focus on joint efforts in 3D medical application

Article
11/9/2020
Three physicians wearing masks; one sitting at a desk, two standing

The JIF award focuses on the Department of Defense/VA 3D Printing Consortium for Medical Applications.

Recommended Content:

Research and Innovation | Technology | DoD/VA Sharing Initiatives

Military Health podcasts provide resources for patients and providers

Article
11/6/2020
Hands holding a smartphone with the Living Beyond Pain podcast playing on the device.

Podcasts have become an increasingly popular way of getting information.

Recommended Content:

Technology | Pain Management | Connected Health

Military medical heroes honored for service above and beyond

Article
11/4/2020
Four military personnel shown during a Zoom call

[T]he service and sacrifice of heroes is “a core strength of our military's resolve and skill."

Recommended Content:

Combat Support

BAMC, Argentine Army medical providers share COVID-19 best practices

Article
11/4/2020
Video teleconference image

U.S. Army South facilitated the virtual subject matter expert (SME) exchange between BAMC and CMMH.

Recommended Content:

Coronavirus | Global Health Engagement | Technology | COVID-19 Vaccine Efforts | Public Health | Convalescent Plasma Collection Program | COVID-19 Vaccine Toolkit

Indiana National Guard amputee stays true to his motto - ‘Never Quit’

Article
11/3/2020
Soldier with leg prosthesis putting on his shoe.

Life and limbs are often casualties.

Recommended Content:

Combat Support | Warrior Care

Military nurses hold virtual research & evidence-based practice course

Article
10/30/2020
Two nurses, wearing masks, examining a mannequin

Due to the COVID-19 national emergency, the three-day in-person course was abbreviated to a one-day virtual.

Recommended Content:

Coronavirus | Public Health | Combat Support | Research and Innovation | Nurses Week
<< < 1 2 3 4 5  ... > >> 
Showing results 31 - 45 Page 3 of 9

DHA Address: 7700 Arlington Boulevard | Suite 5101 | Falls Church, VA | 22042-5101

Some documents are presented in Portable Document Format (PDF). A PDF reader is required for viewing. Download a PDF Reader or learn more about PDFs.